Ohm's Law Calculator

Calculate Voltage (V), Current (I), Resistance (R), and Power (P). Enter any 2 values to solve the other two instantly.

⚡

Enter Any Two Known Values

Fill in two parameters; the remaining two will automatically be calculated.

Volts (V)
Amperes (A)
Ohms (Ω)
Watts (W)

Computed Electrical Values

Active Calculation Formula
R = V / I, P = V × I
Voltage (V)
12.00 V
Current (I)
2.000 A
Resistance (R)
6.00 Ω
Power (P)
24.00 W
Common Quick Examples:
  • Standard USB (5V, 2A): R = 2.50 Ω, P = 10.00 W
  • Household Appliance (120V, 10A): R = 12.00 Ω, P = 1,200 W
  • Automotive Headlight (12V, 55W): I = 4.58 A, R = 2.62 Ω

Complete Guide to Ohm's Law and the Power Wheel

Formulated in 1827 by German physicist Georg Simon Ohm, Ohm's Law constitutes the bedrock principle of electrical and electronics engineering. It describes how potential difference, electron flow, and material resistance interact in electric circuits. Combined with Joule's Law of Electric Heating, engineers obtain the famous 12-formula Ohm's Law wheel.

1. The 12 Ohm's Law & Power Formulas

Depending on which two variables you have measured in your circuit, use the following formulas:

To Solve ForFormula 1Formula 2Formula 3
Voltage (V) in VoltsV = I × RV = P / IV = √(P × R)
Current (I) in AmperesI = V / RI = P / VI = √(P / R)
Resistance (R) in OhmsR = V / IR = V² / PR = P / I²
Power (P) in WattsP = V × IP = I² × RP = V² / R

2. Step-by-Step Practical Circuit Calculations

Consider a practical example: Sizing an electric baseboard heater running on a standard 240V AC circuit that is rated at 1,500 Watts.

  • Find Operating Current: I = P / V = 1,500W / 240V = 6.25 Amperes
  • Find Heating Element Resistance: R = V² / P = (240 × 240) / 1,500 = 57,600 / 1,500 = 38.4 Ohms

Frequently Asked Questions

Ohm's Law states that the current flowing through a conductor between two points is directly proportional to the voltage across the two points and inversely proportional to the resistance. The mathematical formula is: V = I × R (Voltage = Current × Resistance).

1) Voltage (V, measured in Volts): Electrical potential difference. 2) Current (I, measured in Amperes/Amps): The rate of electrical charge flow. 3) Resistance (R, measured in Ohms Ω): Opposition to current flow. 4) Power (P, measured in Watts): The rate of electrical energy consumption (P = V × I).

Electrical power is calculated using Joule's Law: P = V × I. Combined with Ohm's Law, you can also solve for power using: P = I² × R (useful when voltage is unknown) or P = V² / R (useful when current is unknown).

In AC circuits, Ohm's law still applies, but resistance (R) is replaced by Impedance (Z), which accounts for inductive and capacitive reactance: V = I × Z. For purely resistive AC loads (like heaters or incandescent bulbs), standard Ohm's law V = IR remains 100% accurate.

Use the formula: R = (Source Voltage - LED Forward Voltage) ÷ Desired LED Current. For example, powering a red LED (2.0V drop, 20mA current) from a 5V microcontroller pin requires: R = (5V - 2.0V) ÷ 0.02A = 3V ÷ 0.02A = 150 Ohms.

Resistors dissipate electrical energy as heat. The power dissipated is P = I² × R. If a 1/4-watt (0.25W) rated resistor is subjected to 0.5W of power dissipation, it will overheat, char the circuit board, and eventually burn open.

An Ohmic conductor obeys Ohm's Law with a constant resistance over varying voltages and temperatures (like copper wire or metal film resistors). A Non-Ohmic device has a non-linear voltage-current relationship (like semiconductor diodes, transistors, or filament lamps where resistance rises with temperature).

Yes! By entering any two of the four parameters (Voltage, Current, Resistance, Power), this calculator uses the complete 12-formula Ohm's law wheel to solve the remaining two values instantly.

Explore Related Tools

Hand-picked utilities and calculators related to this tool.

Calculator Tools