Concrete Volume & Bag Calculator

Accurately calculate concrete volume in cubic yards, cubic feet, and determine the exact number of 80 lb, 60 lb, or 40 lb bags required.

🧱

Project Geometry

Accounts for sub-base spillage and form deflection.

Required Concrete Materials

Total Concrete Volume
2.72 yd³
Equivalent to: 73.3 ft³ (2.08 m³)
Pre-Mixed Bag Requirements (Inc. 10% Buffer):
123
80 lb Bags
0.60 cu ft/bag
163
60 lb Bags
0.45 cu ft/bag
245
40 lb Bags
0.30 cu ft/bag
Logistics Recommendation:
Order a Ready-Mix Delivery Truck (Exceeds 1.5 Cubic Yards / 68 Bags)
Total estimated dry weight: 9,840 lbs (~4.92 Tons)

Complete Guide to Concrete Volume Calculations & Sizing

Concrete is the most widely consumed manufactured material on Earth. Successfully planning any residential or commercial pour—whether you are constructing a patio slab, installing fence posts, pouring a garage floor, or setting sonotube deck footings—requires precise volumetric measurement to avoid costly over-ordering or disastrous shortages mid-pour.

1. The Rule of 27: Understanding Cubic Yards

In the United States and Canada, concrete is ordered and sold by the Cubic Yard (yd³). One cubic yard is a cube measuring 3 feet by 3 feet by 3 feet:

1 Cubic Yard = 3 ft × 3 ft × 3 ft = 27 Cubic Feet

To calculate the cubic yards of a rectangular slab:

Cubic Yards = [Length (ft) × Width (ft) × (Thickness (in) / 12)] / 27

2. Pre-Mixed Bag Yield Comparison

Bag SizeYield per Bag (Cubic Feet)Bags per 1 Cubic YardBest Practical Application
80 lb Bag0.60 cu ft45 BagsMost economical bag size for medium pours and footings.
60 lb Bag0.45 cu ft60 BagsEasier to lift and carry; ideal for fence posts and repairs.
40 lb Bag0.30 cu ft90 BagsSmall crack repairs, mailbox post sets, light masonry work.

3. Standard Concrete Mix Ratio (The 1:2:3 Rule)

When mixing concrete on-site from raw aggregates rather than pre-blended bags, masonry professionals follow the classic volumetric ratio:

  • 1 Part: Portland Cement (Type I/II)
  • 2 Parts: Clean, washed sharp masonry sand
  • 3 Parts: Coarse crushed stone or gravel (typically 3/4-inch aggregate)
  • 0.5 Parts: Clean potable water (excess water severely weakens cured compressive strength)

Frequently Asked Questions

One cubic yard of concrete equals 27 cubic feet. Based on standard pre-mixed bag yields: You need approximately 45 bags of 80 lb concrete, 60 bags of 60 lb concrete, or 90 bags of 40 lb concrete to produce 1 cubic yard.

The formula is: Length (ft) × Width (ft) × Thickness (ft) ÷ 27 = Cubic Yards. Because thickness is typically given in inches, divide the inches by 12 first (e.g., a 4-inch slab is 4 ÷ 12 = 0.333 feet). For a 10ft × 20ft slab at 4 inches thick: 10 × 20 × 0.333 ÷ 27 = 2.47 cubic yards.

Excavated grade is rarely perfectly laser-level, sub-base gravel settles, wooden formwork bows slightly under liquid hydraulic concrete pressure, and material gets left in wheelbarrows. Adding a 10% safety buffer prevents running out of concrete before finishing the pour (which causes cold joints and structural failure).

As a rule of thumb: If your project requires more than 1.5 to 2.0 cubic yards (more than 65 to 90 eighty-pound bags), mixing by hand in a wheelbarrow becomes exhausting and risks setting before you can screed it level. Order a ready-mix delivery truck for projects exceeding 1.5 yards.

Post holes and structural building footings must always extend below your geographic frost line (typically 36 to 48 inches in freezing climates) to prevent frost heaving from lifting and cracking the structure during winter freeze-thaw cycles.

The standard classic recipe for general-purpose structural concrete is the 1:2:3 rule: 1 part Portland cement, 2 parts clean sand, and 3 parts coarse gravel/crushed stone, mixed with approximately 0.5 parts clean water.

Concrete sets within 24 to 48 hours (safe for light foot traffic). It achieves roughly 70% of its full structural compressive strength at 7 days, and reaches its full rated design strength (typically 3,000 to 4,000 PSI) at 28 days.

A pedestrian sidewalk or backyard patio should be 4 inches thick. A residential vehicle driveway carrying passenger cars and SUVs should be at least 4 to 5 inches thick with rebar or wire mesh reinforcement. Heavy commercial truck drives require 6 inches or more.

Explore Related Tools

Hand-picked utilities and calculators related to this tool.

Calculator Tools